Monthly Archives: August 2016

Know More About Oil for High-Mileage Engines Worth the Extra Cost

Most major oil brands market oil made specifically for engines that have more than 75,000 miles of wear, claiming that additives help reduce engine wear and provide anti-aging benefits. They are often a blend of synthetic and petroleum-based oils, and they typically cost at least a couple of dollars more per quart than conventional oils.
But are they worth the extra dough?
Some oils may be more beneficial than others because they contain conditioners purported to rejuvenate seals to prevent or stop oil leaks, a common ailment in engines with a lot of miles on them.
Internal seals and gaskets become brittle and shrink as they age, allowing oil to seep by. Sometimes this becomes visible as oil stains on a garage floor or as streaks of oil on lower engine parts. When valve-guide seals wear, oil can leak into combustion chambers and the engine will literally start burning oil. With small leaks, blue smoke from burning oil may not be visible from the exhaust, but your oil level will probably drop below the full mark on a regular basis.
The seal conditioners found in some high-mileage oils may reduce or eliminate small leaks and seepage by rejuvenating seals to their original size and shape. If an engine isn’t burning or leaking oil, or if it uses, say, less than a quart over 6,000 miles or so, switching to high-mileage oil may not be worth the extra cost for you. It’s really a judgment call if you should pay more for high-performance oil when your car has 100,000 miles on it but is using little or no oil. It doesn’t hurt and it could prevent leaks from starting. Most vehicle manufacturers would say it’s normal for an engine to consume some oil between oil changes.
In addition to having seal conditioners, high-mileage oils usually boast more detergents designed to clean out sludge inside the engine, plus other additives meant to reduce wear on moving parts. Every oil, though, makes similar claims that it does great things inside an engine.
Some mechanics recommend switching to a thicker (higher viscosity) oil — such as 10W30 instead of 5W20 — or using oil additives to stop oil leaks. Thicker oil makes an engine harder to start in cold weather, reduces oil circulation around the engine and increases oil pressure, which means there will be more pressure trying to push the oil past seals and gaskets.

Should Know How Often Should Tires Be Balanced

Smooth driving is a balancing act that requires getting the wheels and tires to rotate at high speeds without vibrations. That’s not a slam dunk; a dirty little secret about wheels and tires is that they usually aren’t perfectly round, even when brand new. What’s more, their weight often isn’t evenly distributed, so they’re heavier in some spots than others.
Either issue can cause annoying vibrations. Out-of-balance tires can also cause rapid tire or suspension wear, so it’s not just about ride comfort.
That is why when new tires are mounted on wheels they’re spin-balanced to detect vibrations. Some vibrations can be eliminated by rotating the tire on the wheel so the heavy or “high” spot is in a different location that better matches up with the wheel. Small weights are attached to the wheels with adhesives or clips to counteract the heavy spots and provide a smooth ride. Over time, though, the weights can fall off. If that happens to a front wheel, you may feel vibrations through the steering wheel that typically become more pronounced as vehicle speed increases.
Many tire dealers include free lifetime rotation and balancing with new tires (something you should ask about before buying). Tire rotation is when the vehicle’s tires are removed and reattached at a different position to ensure they wear evenly, which should be done every 5,000 to 7,500 miles on most vehicles, or according to the automaker’s recommendation.
Many consumers neglect the balancing part and have their tires rotated only periodically. If balancing was included with the tires, it would be wise to remind the shop to check the balance at the same time. Even if balancing costs extra, it’s a good idea to have it checked at least every two years, or more often in areas where roads are not well-maintained.
Vibrations can also be caused by a bent wheel, a damaged tire (which won’t be fixed by balancing), worn suspension parts or worn wheel bearings, so balancing the wheels and tires may not eliminate all vibrations.
Tires and wheels are balanced before being attached to the vehicle by spinning them on a balancing machine that identifies heavier or stiffer spots that cause vibrations. Some tire dealers and repair shops use “road force” balancing machines that simulate the weight and forces applied to tires and wheels during driving conditions. They say this method provides more accurate and detailed readings that allow more precise balancing.

Simple Tips To Properly Check and Fill Tires

While it may seem like a mundane task, inflating tires is much more crucial to your car than you may think, and it results in a safer and more economical experience on the road. Your vehicle’s handling also will be greatly improved as the larger a tire’s inflated footprint, the more responsive and comfier the ride balance will be.

Because it’s National Tire Safety Week, it’s the perfect time to check your car’s tires.

Before starting

To find your tires’ proper inflation level, look for a sticker on the driver-side doorjamb. It displays the vehicle weight restriction and tire information. The info is also found in the maintenance or car-care section of your vehicle’s owner’s manual.

Don’t refer to the sidewall markings on your tires, which in part specify the maximum tire pressure — not the recommended pressure.

Unless your tire is visibly flat, don’t judge tire inflation just by looking at it; you have to use a tire pressure gauge to get the correct pounds per square inch reading. There are three types of tire-pressure gauges: digital, internal slide and dial. Prices range from $5 for a basic gauge to more than $30 for one that is digital, has an air-release button — or even talks. All will do the job, but you may want to consider the conditions in which you’ll be using your gauge. “We’ve found that low-cost digital pressure gauges are very accurate and maintain the accuracy longer, but in extremely cold temperatures the gauge may not show up properly,” said John Rastetter, Tire Rack’s director of tire information services.

Tips for checking and filling your tires

Tire manufacturers suggest checking tires when they’re cold for the most accurate reading. Outside temperatures can cause tire pressure to vary by as much as 1 psi per 10 degrees; higher temperatures mean higher psi readings. “Tires are black; what does black do? Attract heat,” Rastetter said, noting the importance of finding a shady place to check and fill all four tires.

Temperature plays a huge part in tire psi, Rastetter said, adding that the most crucial time of year to check pressure is in fall and winter when days are shorter and average temperatures plummet.

Check your tires in the morning before going anywhere, because as soon as you get behind the wheel for an extended amount of time, psi will rise. Rastetter said that if you’ve been on the road a long time and notice higher psi in your tires, don’t let the air out, as the increase in pressure has built up due to the warm, constantly-in-motion tires

What to do

1. Pull your car onto a level surface in the shade.
2. Remove dust caps from the tires’ valve stems.
3. Using your tire gauge, firmly press the tip of the gauge straight on to the tire’s valve stem for a brief moment.
4. The tire gauge should provide a psi reading; if the number seems unrealistically low or high — for example, 85 psi or 1 psi – you will need to repeat the previous step, ensuring that the tire gauge’s tip is properly making contact with the valve stem.
5. If the tire gauge’s recorded reading is higher than the manufacturer-recommended rating, press the gauge tip on the valve stem until you hear air leak out. Check the tire pressure again.
6. If the reading is lower than recommended, fill the tire with air by firmly pressing the air-hose tip onto the valve stem. You will hear air quietly enter the tire. If you hear air leaking or spraying out, you need to double-check that the connection between the air hose and the tire’s valve stem is secure.
7. When you think you’ve added or let out enough air, check the pressure a few times with the gauge.
8. Replace the valve dust caps. Rastetter emphasized the importance of keeping dust caps on during winter driving because if water gets into the valve stem and freezes inside the tire, it could cause a flat.